IP65防水防爆配電箱

安裝、調整使用與維護

用戶在安裝之前應檢查配電箱銘牌上所列數據與說明書中基本參數是否相符，并應詳細檢查配電箱內部是否正常，元件是否損壞，導線是否松動、脫落，螺釘是否松動、缺少；

安裝時應注意電纜由出線套、金屬墊圈、橡膠密封圈依次放入引入裝置內，待接好線以后，將出線套旋緊，使之嚴格密封，再將壓線板安裝好，防止電纜拔脫；

經檢查無誤以后，接好進出線和內外接地線，即可通電使用；

檢查與維修必須在斷開前級電源后方可進行，并嚴格禁止在大蓋打開狀態下進行通電試車（在安全的情況下除外），檢修完畢后應關好大蓋，并把螺栓緊固好才能通電使用；

檢查與維修過程中，不得損壞隔爆面，并應保持清潔，合上大蓋前應涂204－1置換型防銹油。

IP65防水防爆配電箱

保管及運輸

配電箱應放置在不能受支陽光直接照射和雨雪淋濕的倉庫中保管，不得傾斜、倒立放置；

配電箱在運輸過程中應防止劇烈巔簸、振動和受到外力撞擊、磕碰的現象，并按照工作狀態進行放置。

功用

戶外防雨型不銹鋼防爆配電箱是按電氣接線需求將開關設備、丈量外表、維護電器和輔佐設備組裝在關閉或半關閉金屬柜中或屏幅上，構成低壓配電裝置。正常運轉時可憑借手動或自動開關接通或分斷電路。毛病或不正常運轉時憑借維護電器堵截電路或報警。借丈量外表可顯現運轉中的各種參數，還可對某些電氣參數進行調整，對違背正常作業狀況進行提示或宣布信號。常用于各發、配、變電所中。